Powerspec g914 Bluetooth not working

Options
I have tried using Bluetooth and it is not working, I have tried updating it but it says no suitable drivers. Looked for it in device manager and it’s not in there. Checked my antenna and it’s connected it just snaps in. Any chance some one had the same issue how did you fix it? 

Answers

  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @Kodakjedi

    WIFI works? Unplug the system for 30 seconds then power it back on and check device manager again. There's nothing at all under 'Bluetooth'?

  • Kodakjedi
    Options
    @PowerSpec_MikeW just did that sorry I work nights and have barely touched my pc but there’s literally nothing in device manager that says bluetooth
  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @Kodakjedi

    It's an integrated module with the WIFI. WIFI is working fine, correct?

  • Kodakjedi
    Options
    @PowerSpec_MikeW
     yes WiFi is working fine, I don’t see a WiFi either should I just take it to MC and see if they can see what’s wrong with it I just bought it a couple weeks ago
  • Kodakjedi
    Options
    @PowerSpec_MikeW
    this is the only thing that shows up on network 
  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @Kodakjedi

    The WIFI is fine. We'll probably need to swap the board out on this one.

  • Kodakjedi
    Options
    @PowerSpec_MikeW just came back out of the blue 
  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @Kodakjedi

    That's different. Keep an eye on it, we'll replace the module/board under warranty.

  • pandarian
    Options

    I have the exact same problem on the exact same system. did you ever find a permanent solution to this?

  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @pandarian

    First thing is always to discharge the system, I've seen that happen a few times. Usually it's a one off.

  • pandarian
    Options
    It’s a recurrent issue for me. So I have tried everything including resetting cmos (which will make it work until the next restart), turning off fast startup, reinstalling Bluetooth drivers. Bluetooth sometimes disappears completely and sometimes shows up with broken driver that needs to be uninstalled and it tends to happens after the pc is shut off for a while. WiFi is always rock solid the entire time. What has helped in the past couple of days (fingers crossed) is that I moved my controller dongle from a usb 2 port to a usb 3 port. If this is a permanent fix, then it’s probably because the Bluetooth chip set is sharing power draw with the usb 2 ports. Maybe this’ll help someone else’s Bluetooth woes.
  • pandarian
    Options

    ok i spoke too soon, after 9 days the bluetooth problem came back. Needed another cmos reset before the bluetooth was recognized again. This is getting frustrating.

  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @pandarian

    Next step would be checking the card is seated properly, but I believe it's under the I/O on this board. We'll replace the board under warranty.

  • pandarian
    Options

    hmm, i can't seem to find the location in the manual, can you link a picture/schematic? My worry is that the problem is so intermittent and random that it won't be reproducible when I bring it into the store.

  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @pandarian

    Looks like it's mounted vertically behind the antennas, it would be quite a job to get to. You'd certainly have to remove the board. Let us just get you a new board.

  • pandarian
    Options

    ok, how do I get the process started? I actually went though powerspec phone support without a definitive fix. I can bring it into the store but hopefully they don't make me go through the diagnostic process again.

  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @pandarian

    The store would need to diagnose it. The problem is, by the time you get there, discharging it in the process, it may be working again. But we need to go through the process. I would setup service in the store and let me know what the outcome is. We'll go from there.

  • pandarian
    Options

    yeah, not looking forward to a 3 hour trip for this especially if they won't replace the board.

  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @pandarian

    Give them a shot to handle it. If it's not solved, let me know and I'll figure something out.

  • pandarian
    pandarian
    First Comment
    ✭
    edited February 16
    Options
    Ok microcenter did a diagnostic and can’t replicate the problem. They did offer to replace the entire pc with a new one but there weren’t any in stock. I’m trying to see if they can replace the motherboard either way.
  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @pandarian

    Let me know. We just finished our inventory, so units should be replenished soon.

  • pandarian
    pandarian
    First Comment
    ✭
    edited February 16
    Options

    so I was able to recreate the problem pretty consistently (not everytime). It happens when I have more than 1 usb 2.0 ports in the back used for 2.4ghz wireless dongles for keyboard/mouse/controller and put a SSD in the m.2_4 slot. Bluetooth will disappear in device settings and under USB it will have a problem with a usb device. If i unplug the dongles and/or use only usb 3.0 then the issues gets resolved with a simple restart, otherwise it requires a power discharge. Seems like utilizing the usb 2.0 ports causes overloading of the chipset bandwidth and/or power somehow. Or maybe the board is confusing the dongles for the onboard bluetooth on boot when plugged to usb 2.0.

  • PowerSpec_MikeW
    PowerSpec_MikeW
    Seventh Anniversary 2500 Comments 100 Answers 250 Likes
    PowerSpec Engineer
    Options

    @pandarian

    That makes more sense. I've seen issues like this, and generally the main factor is if the ports are run via chipset or CPU directly. Please list the devices with brand and model.

  • pandarian
    Options
    Logitech k400, gamesir g7 pro wireless, crucial p3 plus.

Leave a Comment

Rich Text Editor. To edit a paragraph's style, hit tab to get to the paragraph menu. From there you will be able to pick one style. Nothing defaults to paragraph. An inline formatting menu will show up when you select text. Hit tab to get into that menu. Some elements, such as rich link embeds, images, loading indicators, and error messages may get inserted into the editor. You may navigate to these using the arrow keys inside of the editor and delete them with the delete or backspace key.

We love seeing what our customers build

Submit photos and a description of your PC to our build showcase

Submit Now
Looking for a little inspiration?

See other custom PC builds and get some ideas for what can be done

View Build Showcase

SAME DAY CUSTOM BUILD SERVICE

If You Can Dream it, We Can Build it.

Services starting at $149.99