My ender 3 pro did not come with the bottom m5x45 screws. Do you know how I could get them?
Hello, so I was trying to assemble my new printer, but I think I overscrewed the limit switch and it led to a crack on top. If I need a replacement, where could I get one?
I am trying to get this going since my Creality Direct Drive kit runs the extruder in reverse now and can you believe it, Creality doesn't seem to bother to compile a firmware for their own kit :( I installed Visual Studio and installed PIO and the Marlin Auto Build, then the only file I edited was the configuration.h to…
I am wondering if there are any Material Safety Data Sheets available for the Resins and Filaments that are available through Micro Center stores. More so for the resins then the spools of filament. Thanks, Doug T. Edited to fix spelling error from typing original question out on phone.
I have noticed much lower stock of filament at my local Microcenter store. Most of the filament colors and types are out of stock in store and online. Is this a supplier change issue or is printing filament getting discontinued?
Hello and thanks for the acceptance to your group. I just bought an Ender 3 pro, assembley seemed to go well. When I tried to auto home it went to the correct corner but went a few mm past the end of the bed towads me. I was proper on the left side of the bed just a little long on the Y axis. Any suggestions would be…
Can you change the extruder on these? If so, how and where can we buy a new one for it? The left one is not to be working as well as it use to.
I recently bought an ender 3 pro from MC in st davids. The plate is warped and the middle is higher than the rest of the plate making it impossible to level the bed. Can I package it back up for a refund or replacement at the store? I purchased just a few days ago. Thanks!
So I'm working on a prototype for my design but the final product will more than likely be made of High-Density Polyethene. The problem is that HDPE is SUPER difficult to print with and very difficult to even find. I am wanting to know if anyone has any good substitute ideas that would be similar to HDPE? I've already…
I have tried watching some videos on youtube but i still cant get it to work
I purchased a Creality Ender 3 v2 printer for my sons birthday. All it prints are blobs. Will pay good money to have someone come out and set up correctly and configure. In the Rochester Michigan area.
I was setting up my slicer and checking the product profile and couldn't find the optimum layer height in the specs for the resin I have the Inland standard grey resin shown here: https://www.microcenter.com/product/625170/405nm_LCD_UV_Curing_Resin_Standard_Photopolymer_Resin_for_LCD_3D_Printing_500G_-_Gray I was wondering…
Hello all! If you have any empty Inland spools, don't throw them away! Send or bring them in to IC3D Printers in Columbus, Ohio! We do a lot with 3D printing and would like to minimize the environmental impact of 3D printing by collecting and putting empty Inland brand reels to use. More information here:…
New revisions of the BL touch are starting to hit stores, this revision plugs directly into the bltouch plug on the motherboard and comes with updated instructions that are decades better than the old ones
https://www.chitusystems.com/2020/11/03/how-to-activate-the-wifi-module-function-on-your-3d-printer/ For the H and the R follow the instructions for the esp-01 and use sku 030197 to get going! For the ld-006 follow the instructions for ethernet! (though all the motherboards have slots on them you can solder an ethernet…
A few days ago I bought a Creality Ender 5 at Micro Center (Virginia). I managed to damage two of its 5x30 screws, causing their washers to be near the tip of the screw instead of near the head (photo below). Does anyone know where I can purchase replacements, or maybe how to fix the issue? In this form, I'm unable to…
I was buying the Natural Inland PLA, it came in a white box, and it was awesome. Now I just bought some natural PLA and it came in a grey box and it is different and is more brittle. The suggested temperature ranges are also different, so it seems like an entirely new formula. The white box says "new and improved formula"…
I am looking to buy a 3D printer under $300, this is for my maker wife who can build, program and fix about anything - normally I would go to your store and get recommendations but I am avoiding going into stores. I have done some research and see the Creality Pro is on sale and gets good reviews. Would this be what you…
Bought an Ender-3 V2 also bought a auto bed leveling sensor for the 3D printer however when the gift was open it was noted that the auto bed sensor which is a (BLTouch) was labeled for a use with a Creality V1 mainboard and not for a V2 main board is this sensor compatible with my Ender3-V2 or do I need to return and get…
So I recently saw that microcenter now sells petg+ and lite pla but there isnt any clear indication how these new filaments vary from their regular petg, pla and pla+ aside from extruder temperature ranges. Does anyone know the actual differences with these new filaments?
I have a Ender 3 Pro that has been upgraded with a extender kit for a larger build plate, skt mini 3 control board, and I would like to finish the install of a BLT auto leveling probe... only I have had fits trying to re do the code as shown on many You Tube videos... I am not any kind of a programer... no speller it…
On an Ender v3 pro I am adding a laser, can I use a switch to select printer or laser?
For those who are new to VR gaming and have just picked up the Oculus Quest 2, I have found this app on the system to be a great way to get your feet wet and it's free!!
Recently I decided to print a case for my PiGrrl 2 with the Atari logo on it. PiGrrl is a series of Raspberry Pi powered portable emulation consoles produced by Adafruit. PiGrrl 2 is the most recent version to use a full-sized Raspberry Pi, so it’s more powerful than the three other versions. Here’s a picture of the…
Micro Center has been working with hundreds of healthcare professionals and organizations to help make a difference in the fight against COVID-19. Our fleet of 3D printers have been busy printing face shields based on the open source design by PRUSA Research (who has already printed and donated over 35,000!) to support…
Do you have the material and equipment in stock to start producing these? How much is the equipment and given the consumables what is the cost/mask. I would like to help address the pandemic if possible.
Submit photos and a description of your PC to our build showcase
See other custom PC builds and get some ideas for what can be done
Services starting at $149.99